How to Powder Coat: 9 Steps (with Pictures) - wikiHow (2025)

Explore this Article

Co-authored byAlvaro Mendoza, PhD

Last Updated: July 11, 2024Approved

Download Article

1. 1

   Determine the type of material you are going to powdercoat and then select a suitable powder for the finish. Powdercoating is done with thermoplastic or thermoset polymer powder, and these materials are formulated for bonding with different base metals to give the best results.

   • See the next section for a detailed discussion of the differences between thermoset and thermoplastic coats. What's good for a car may not be good for a small trinket or decoration.
2. 2

   Disassemble all threaded or lubricated interfaces before you begin, including anything you don't want coated. It sounds simple, but many people forget this step. The powder coat you apply will adhere to everything (if properly done) on your rig, making sealed surfaces, bearings, clamps, bolts and nuts, etc. useless after blasting.^[1]

   Advertisement

3. 3

   Clean the base metal thoroughly.^[2] Using bead or abrasive blasting on hard metal, such as cast iron or steel, will remove mill and rust scale, dirt and foreign materials. Chemical solvent cleaning will remove any grease, oil, or paint, and light sanding can be done to finish preparing the surface. Aluminum, magnesium, and other soft alloy metals can be solvent cleaned and wire brushed, or sanded if needed.

   • For example, you might sand-blast whatever you want to powder coat until it's down to bare metal. This is the first step in the process. If you don't have access to a sandblaster, you can also use a wire wheel, bench-grinder, or even sandpaper. Just as long as you get the material down to bare metal.
   • The next step is to strip the metal of any remaining grime or gunk. You can achieve this by soaking the item in acetone (if the item is small enough) or by wiping it with an acetone-soaked rag.
4. 4

   Apply the powder to the object to be powder coated. This is done using a "gun" or compressed air sprayer which electrostatically charges the powder material so that it sticks to the grounded base metal object receiving the coating. These guns are available from various suppliers, and cost as little as $100. For experimental purposes, you can apply the powder to a flat metal surface by dusting it directly on, and spreading it to a thin, even layer.

   • Make sure you have your electrostatic charge hooked up to whatever part you are coating. The powder you use won't properly adhere unless it's given a charge to hold onto.
   • After applying the coat but before curing, be careful not to brush or blow on the powder coat, as this will cause some of the powder to fall off, leaving you with a less precise coat.
5. 5

   Cure the metal at a temperature appropriate for the powder material you use. A conventional oven is suitable for this purpose if the metal is small enough to fit, otherwise, an infrared heat lamp or other flame less heat source needs to be used. Normally, the object is heated to 350° to 375° F (175° to 190° C) for about 10 to 15 minutes, and allowed to cool.^[3]

   • You can use a conventional oven to powder coat smaller items. Just be sure that you won't be using the oven to cook food after the powder coating. Once you've used an oven to powder coat, it absolutely should not be used for cooking.

Advertisement

Download Article

1. 1

   Use thermoplastic coatings for items you might eventually remold, and thermoset coatings for items that will remain essentially permanent. The main difference between thermoplastic and thermoset is the reversibility of the coat. Like their name implies, thermoset coatings cannot re-melt after undergoing an irreversible chemical bonding process. Conversely, thermoplastic coatings can remelt because no chemical process takes place.

   • Thermostat coatings are ideal for things like electronics and appliances because they need to withstand higher amounts of heat, which might cause thermoplastic coatings to melt.

   See Also

   Vor- und Nachteile der Pulverbeschichtung | AblisonWhat Is Powder Coating? Types, Process & BenefitsPulverbeschichtung: Alles, was Sie wissen müssenAlles, was Sie über Pulverbeschichtungen wissen müssen: Haltbarkeit, Verfahren und mehr
2. 2

   Choose thermotype based on some of the features of the coat. Thermosets and thermoplastics have different chemical properties, making them ideal for different uses. Knowing some of those properties can help you choose which type to coat with:

   • Thermosets are said to reinforce the structural integrity of an item, making them particularly suitable for heavy wear-and-tear. They also supply the item with superior chemical and heat resistance, as mentioned above.^[4]
   • Thermoplastics offer a mixture of strength and flexibility. They are commonly used for items such as plastic bags and even mechanical parts.
3. 3

   Know the advantages and disadvantages of thermosets. Thermosets are often used to coat appliances because of the heat they can withstand.^[5]

   • Advantages: beautiful aesthetic look; cheap; added strength and stability; resistant to extreme temperatures.
   • Disadvantages: irreversible process means thermoset can't be recycled; more difficult to finish; can't be reshaped.^[6]
4. 4

   Know the advantages and disadvantages of thermoplastics. Thermoplastics are used for many items, such as park benches, that require both plasticity and durability.^[7]

   • Advantages: high lubricity or tack;^[8] recyclable; able to remolded and/or reshaped; increased impact resistance.
   • Disadvantages: more expensive (usually); can melt off if overheated.

Advertisement

Expert Q&A

Ask a Question

Video

Tips

Thanks for submitting a tip for review!

Warnings

Things You'll Need

9 votes - 100%